高端电压小功率检测仪（耐脉冲检测仪）-（测算机控制）

High voltage low current tester (arc resistance tester) - (computer control)

产品的名字：耐电弧试验机

Product name: electric arc resistance tester

车辆机型：NDH-A

Product model: NDH - A

满足了标准：GB/T 1411-2002《固态垃圾绝缘电阻材质耐高放低电流大小电孤蓄电池放电的实验》（等一起IEC  61621-1997）及ASTM D495等规则的必须规划研发的，并具备IEC 149、UL 746A等试验报告措施

Meet the standards: GB/T 1411-1411 "solid insulating material resistant to high voltage low current arc discharge test" (equivalent to IEC 61621-1997) and the requirements of standards such as ASTM D495 design and manufacturing, and conform to the IEC 149, UL 746 a test method, etc

一 概述

一An overview of the

最主要实用空间及功能键：

本耐压机是遵照广泛应应用在伺服电机、家电和家廷用家电等行业领域的高压电工用塑胶片、不饱和光敏树脂胶和隔热漆等隔热的原食材的耐脉冲的性能指标鉴定，主应用在物质隔热的原食材如：塑胶片、透气膜、不饱和光敏树脂、云母片、陶瓷图片、玻璃纸、隔热油、隔热漆、纸箱等有机溶剂的耐脉冲的性能指标测验；

本可靠性冲击试验机由算出机控制电脑运行，应该凸显现今检测环境及检测时间间隔，检测停止后并保管现今检测数剧，并可网页打印.标准化实验上报上报。

Main scope of application and features:

This machine is in accordance with the applied in motor, electrical appliances and household appliances and other industries with varnish insulation materials such as plastic, resin adhesive and the arc resistance evaluation, the main used for solid insulating material such as plastic, film, resin, mica, ceramic, glass, insulating oil, insulating paint, such as cardboard medium arc resistance test;

This testing machine controlled by computer operation, can display the current experimental condition and experimental time, after the experiment, and save the current experimental data and can be printed. Standard experiment report 

二 功能特点

1 机器为上下两边集成格局，底端为作业体系，上面为耐压湿热。

2 本货品主要采用*新自动化调节技术工艺，经由抉择软件（IEC或ASTM）可自行采取应力测试，并在线上上出现试验报告操作过程和没想到。

3 **机械性能优异，抗干扰信号专业能力强，检测可靠性强，精密度不高。

二：Functional features：

1 this machine is up and down a body structure, lower for the operating system, the upper part of test cases.

2 this product USES the latest intelligent control technology, through the selection process (IEC) or ASTM test can be automatically, and displayed on the computer and the test process and results.

3 good safety performance, strong anti-interference ability, high test precision. 

三 主要技术参数

1 焊弧通断用时粗差：小于等于 ±10ms

2 调压器出水量：2kVA

3 额定的经过多次实验发现电流：12.5kV

4 检测的电压精确度：±3%

5 电流大小把控导致精度：±10%  电压电流量测控制精度：1.5%

6 金属电极对制样压：（0.5±0.05）N

7 电极片相关材料：钨棒

8 电级时间：（6.35±0.1）mm（IEC）

               （6.0±0.1）mm（ASTM）

9 动用环保热度：（23±2）℃

10 利用生活环境温湿度：（50±5）%

11 外接电源：220V±5%  50Hz  10A

12 试验报告    的办法：   行业标准/美标/10 mA 接连/20 mA 多次/30 mA重复/40 mA累计

13 冲击试验程序流程给出：

Three main technical parameters：

Error: 1 arc on-off time less than plus or minus 10 ms

Transformer capacity: 2 kva

3 test voltage rating: 12.5 kV

4: test voltage accuracy + / - 3%

5 current control accuracy: plus or minus 10% current measuring accuracy: 1.5%

6 electrode pressure on sample: (0.5 + 0.5) N

7 electrode materials: tungsten rods

8 electrode distance: 6.35 + / - 0.1 mm (6.0 + 0.1) mm (IEC) (ASTM)

9 using the environment temperature (23 + 2) ℃

10 use environment humidity: (50 + 5) %

Power supply: 220 v + 5% for 50 hz 10 a

Test method: beautiful mark / 10 gb / 30 mA mA continuous / 20 mA continuous/continuous / 40 mA continuous

13 test procedure is as follows:

Procedures section of the arc current

MA arc on-off time s the program s test total duration time s

IEC 61621 ASTM D495

1 1/8 10 s on 7/8 s broken 1/4 7/4 break 60 s 60 s

2 10 1/4 "s pass 3/4 s 1/4 3/4 break 60 s 120 s

3 to 10 1/4 "s make a quarter s break a quarter of a quarter break 60 s 180 s

4 consecutive 10 to 60, 240

5 20 consecutive 60, 300

30 consecutive 6 to 60, 360

7 consecutive 40 to 60, 420 

四  配置

Four configuration：

Serial number name number note

01 arc resistance tester

02 a electrode system

03 electrode bearing a set

04 a set of power cable

05 ground put a rod

06 milliammeter current one

7 a set of computer measurement and control software

08 specimen holder a

09 electrode distance standard 2 blocks

Standard 2 blocks of 10 Angle

11 ceramic pieces 2 pieces

12 one brand inkjet printer

13 1 computer brand

14 1 instruction manual

15 1 certificate

五 食品型号规格：

NDH-A    耐脉冲耐压仪-微机设定

NDH-B    耐焊弧经过多次实验发现仪-摸屏操控

Five product model:

NDH - A arc resistance tester - microcomputer control

NDH - B arc resistance tester - touch screen control
ASTMD495耐高压低电流电弧放电试验机详情可以随时来电咨询！